• Washington
  • robinwcc2@gmail.com

Dealing with toilet leakage is definitely a major inconvenience. Not only do we have to spend hours and hours cleaning the water that runs out of the basin, but we also have to deal with the stagnant sewage gases, responsible for the odor.

As a possible solution, many people use the famous silicone, truly believing that the disorder will be remedied.

In fact, few people know, but that white silicone wrapped around the toilet has its purpose to be. To prevent standing water in the vase from running, it is necessary to pass some resistant material around the container to seal it.

But, we are sorry to say that silicone alone is not enough. Perhaps, your problem will be solved for a while in a palliative way, but it is no guarantee of an effective solution. So, how to maintain the toilet and prevent possible leaks?

After all, why do toilets end up leaking?

The most common cause for the leaking of toilets is related to the sealing ring, responsible for holding the water from the basin and taking it to the sewer system, where this water will receive the proper treatment.

The gasket is a very simple and easily recognizable piece. As the name implies, the piece is shaped like a ring, which can be made of different materials – from rubber to wax.

Generally, gaskets tend to last for a long time, even longer than the toilet itself, but it may be that over its lifetime the part will break or have some crack that leads to leakage.

See also  How to Prevent a House Lockout

When the gasket is broken or worn, there is no way. The part must be replaced immediately, otherwise the toilet will leak from underneath.

Another factor that can lead to the replacement of the sealing ring is poor installation, after all, if it is poorly positioned, it does not tend to obstruct the passage of water, which can lead to leaking of the sanitary ware.

Clearly, the biggest sign that it’s time to change the ring is the perception of water leaking at the base of the dishes, but if you start to notice water decompression, it could be a sign that the ring is poorly fitted or that the sanitary ware is loose.

The piece is not difficult to find, being present in several construction stores, and its installation does not require so many materials, it only takes a few tools.

How to seal the toilet without error:

When they notice a leak in the base of the sanitary ware, it is common for many people to turn to silicone. Therefore, they pass the material around the vessel and hope that it will be able to stop an internal problem.

They are not entirely wrong, the white silicone, bought in construction stores, is essential to keep the toilet bowl fixed and stop the water that has remained there. Essential but not enough.

It is crucial when installing a toilet that the sealing ring is very well fitted, otherwise the external seal will do nothing. Learn now how to properly seal the toilet bowl.

See also  Get a stylish look with floor standing bathroom cabinets

1. Remove the toilet bowl:

The first step is to remove the vessel and to do this it is necessary to remove the safety screws that secure the compartment to the floor. Another important point is to remove the silicone around the vessel so that its removal is easier.

That done, now it’s time to get down to business. Move the piece, turning it slowly to make sure it is completely free of the floor. When you notice that the piece has completely detached, lift it and remove all the internal water. Later, dispose of it in a place where it is not likely to break.

2. Remove the sealing debris:

Now everything will depend on what you will find when you take the basin. It is possible that the vessel was installed without a sealing ring, which explains the cause of the leaks and the bad smell.

On the other hand, it is possible that you may still find the sealing ring in wear, if applicable, use a spatula to remove the remaining material, both what is attached to the flange and what is left in the basin, just be careful when handling the piece so as not to break it.

Then, remove excess grout from the floor and sanitize the space to prepare for installing the gasket.

3. Install the gasket:

For the installation of the sealing ring, it is important to consult the manufacturer’s recommendations, considering that wax rings can be found in adhesive form and can be glued directly to the base of the vessel or to the water outlet pipe.

See also  Fantastic Flowers Gardening Approaches to Decorate Your Backyard

After ensuring that the ring is already well fitted, apply the grout to the floor only on the circumference of the pelvis. Center the toilet on top of the grout, making sure the holes in the dishes are aligned with those in the base. Just don’t forget to put the screws back.

4. Finishes and tests:

Sequentially to the installation of the toilet, clean the excess grout before it dries and becomes difficult to remove. To level the base with the floor and make sure the ring will compress, sit on the toilet lid repeatedly so that your weight presses into the ring. Tips you should know before drilling

After placing all the parts in their proper places, open the valve and press the flush to make sure the leak is resolved.

Did you see how in just a few steps you can solve the inconvenience without much effort? Now, if you’re dealing with clogging toilets, no problem.

If you liked the post, be sure to share the content with friends and family. Thus, you help more people to have access to functional and powerful tips to put an end to toilet leaks.

Shabbir Ahmad

Shabbir Ahmad is a freelance enthusiastic blogger & SEO expert. He is the founder of Shifted Magazine & Shifted News. He contributes to many authority blogs including porch, hackernoon & techcrunch.